Mad Of Electronics

Here u can find some useful tips and links related to troubleshooting electronic appliances
Showing posts with label junk. Show all posts
Showing posts with label junk. Show all posts

Electricity From Water

Posted by rajascientist Sunday, August 23, 2009 0 comments

Simple Battery

Following the below procedure you can make a simple battery ,by just using water as a electrolyte.

Things needed:

  1. Water
  2. Zinc plate
  3. Carbon rod
  4. Waste battery

This simple battery needs two electrodes Zinc and Carbon .These electrodes can be easily obtained from junk batteries.

How to remove carbon rod:

First of all remove the external metal covering of the battery carefully.Now the layer covering the battery is nothing but Zinc .



After removing the plastic cover ,carefully remove the carbon rod by pulling at the top. You can get a black rod that is nothing but the carbon rod.


Leave all those black powder which is of no use for us .Now the zinc plate and carbon rod are going to act as a electrode.

Battery:

Take a glass full of water immerse these two electrodes, now check the voltage using multimeter.By connecting two or more such cells you can produce voltage enough to light a LED.


For more voltage add some acid to water ,so that the conductivity of water increases.You can add lemon ,citrus juice to water which are acidic in nature .

Getting Laser Diode:

How to remove laser diode from a junk Dvd player , this is the most common question.Finally the answer in revealed below.

Below is the picture of laser lens set acquired from a junk Dvd player.



At the center is lens ,surrounded by focus adjustment coils.But our point of focus is laser diode. For your convenience i have removed the laser diode separately.


Once you have located the laser diode you can remove it by cutting the strip.Now you have got a four pin laser diode.

Polarity of diode:


Our next task is to find the polarity of the laser diode. With simple technique it can be done easily. Place the diode on the ground such that the pins face the sky , now look at the bottom of the pin , you can see a black stud in all the three pins except one which is the ground pin .



Now look out for the positive pin ,the pin right to the ground pin is usually the positive ,in some case the pin left to the ground acts as positive.

Laser beam:

To check the diode use two batteries ,so that a steady 3v can be obtained. Most of the laser diode operate at 3v ,any thing above 3V may spoil the diode,be careful.

The moment you connect your battery ,you can see a beam of red laser gushing out. This beam can be focused in to a single point by using collimating lens .


For more powerful laser look for CD or DVD writer , laser diode.

Don't look at the diode directly ,you may end up damaging your eye.

AUDIO AMP FROM JUNK CD PLAYER

Posted by rajascientist Wednesday, August 12, 2009 25 comments

Many junk electronics gadgets can be used to get some useful spare parts and some times amplifier circuit,transmitter,receiver etc.,


I got a junk CD player a few weeks back i opened it and took some useful things some motors,laser diode, IR receiver, and finally a Dual channel Audio amplifier.



The IC was CD6283CS and its specifications are as follows


4.6 W x 2 dual-channel audio power amplifier

Model: CD6283CS

Product Name: Dual-channel audio power amplifier
Overview and Application: CD6283CS is one pair of channel audio power amplifier can be used in portable and hand-made audio power amplification


Features:
1). Large output power

2). Boot "sound of escaping laughter" small voice
3). Quiescent current small

4). Soft clamp function

5). Built-in overheating protection circuit
6). Wide range of supply voltage: VCC = 6V to 15V Package: FSIP12


I took that amplifier circuit and assembled it in another small case ( i used a junk fish tank motor).


I just drilled four holes to accompany two volume control , one Bass and One Treble. Now i fitted the main amplifier board and took out all the connecting wires.














Now I got a handy audio amplifier which i can use it for my hobby projects.

Search This Blog

Share

Share |